Browse all practice questions for the Electrical Job Information Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Electrical Job Information Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • As trees grow, what gas do they absorb and what gas do they release?
  • What is a crucial responsibility of entry supervisors in a confined space?
  • What type of assembly is considered a fire-resistive wall or floor?
  • Which of the following is a type of boom lift with a telescoping design?
  • What type of lift is considered scaffolding?
  • Conductor pulling ropes are specifically designed for what attribute?
  • Which of the following can be a part of a fire-resistive assembly?
  • When using a set-screw type pulling head, the conductor should fill what percentage of the barrel connector's cross-section?
  • Which of the following is NOT included in a complete through penetration firestop system?
  • What term describes the ability to communicate effectively and avoid offense in interpersonal relations?
  • What is the maximum annular space allowed between a listed electrical box and a two-hour rated wall without requiring penetration protection?
  • What happens to the metallurgy of a metal tool when heat is applied?
  • What does tooling the caulk improve besides appearance?
  • Which of the following actions must an employer take regarding the location of energized electric circuits?
  • What is the purpose of tinning the conductor in low-voltage electronic cables?
  • What is generally the first step in using a pipe wrench?
  • Manufacturers refer to number 14, 12, and 10 AWG size conductors as what type of conductors?
  • When setting up scaffolding, which is a preferred method of achieving stability over using blocks?
  • What type of pulling aid serves more than one purpose and has measurements along its length?
  • A confined space is considered dangerous if it has the possibility of engulfing an entrant. What is one condition that could lead to this situation?
  • What is the minimum bending radius for cables with an overall diameter of one inch or less?
  • If one or more entrants suffers an injury or illness and is unable to exit the confined space without help, who must initiate a rescue?
  • What kind of strap is typically used for mounting EMT and rigid or IMC pipes?
  • Which type of connector is typically used with flexible conduit systems?
  • Which type of coupling is used with flexible metal conduit (FMC)?
  • Which type of construction is categorized as 'Wood Frame Construction'?
  • Locking receptacles are primarily used in applications where what is a major concern?
  • What is the first step in constructing a concrete frame building?
  • What is the main hazard associated with wearing rings and jewelry for electrical workers?
  • What is the purpose of a handy-box round mud ring?
  • How often must Type AC armored cable be secured?
  • Which tool type is used specifically for electrical applications?
  • Which tool is most appropriate for loosening or tightening fasteners with a square head?
  • What does a twist bit primarily do?
  • How are structural steel beams rolled?
  • Which wrench is specifically designed to prevent damage to the surfaces of pipes?
  • How does corrosion affect the performance of a conductor in low-voltage electronic cables?
  • How many classifications are there for concrete blocks based on the weight of the mix?
  • In concrete frame construction, what does it mean when beams, columns, and floors are described as monolithic?
  • What is the temperature requirement that a 1-hour fire-resistive assembly must withstand during testing?
  • What type of procedure must contractors on the job site follow?
  • For electrically-driven equipment, how must the footswitch be positioned to allow operation?
  • What two characteristics of a conductor are affected by lay length?
  • What is a significant advantage of using a pulling grip?
  • What is the correct method for handling reels while operating a forklift?
  • How are strength requirements expressed in relation to cable support?
  • Which of the following is NOT an advantage of building with concrete?
  • What should be reviewed as part of the cable pull safety check?
  • Isolated ground receptacles must be identified by what?
  • What is the recommended distance for anchors from an unsupported edge?
  • Which of the following scenarios indicates a current level that can cause involuntary reactions or injuries?
  • An offset screwdriver can come with which types of blades?
  • The actuator on a switch comes in how many different basic styles?
  • In construction, what is the purpose of formwork?
  • True or False: In concrete construction, it is advantageous for beams, columns, and floors to be poured at different times.
  • What is the most basic division of wire and cable technology based on?
  • What temperature rating is deemed safe for installing non-metallic sheathed cable?
  • When testing a through penetration system, what is the outcome of UL testing various manufacturers' products in the assembly?
  • What is the temperature rating limit for the ampacity of non-metallic sheathed cable?
  • When conducting a rescue in confined spaces, can an offsite rescue team be utilized even if an onsite team is available?
  • In the event of an injury during a confined space operation, who is primarily responsible for managing the rescue?
  • What does the F rating indicate in relation to firestop systems?
  • What type of pulling heads utilize opposing set screws to secure the conductor?
  • Cable tray cleats are primarily used for what type of cables?
  • When penetrating a concrete fire-resistive wall with RMC, is it acceptable to use mortar to fill the annular space?
  • What is the main benefit of using 25 gauge studs in interior walls?
  • Which type of cable is specifically designed for indoor residential use?
  • Which tool is designed with low breakage strengths and is used to aid in wire pulls?
  • Which tool is primarily used for cutting wires and cables that are often difficult to reach?
  • In a through penetration system, what is affected by using different manufacturers' products?
  • At what current level is extreme pain and the possibility of death likely?
  • When can an employee approach an energized electric circuit without proper protection?
  • If a listed through penetration does not specify caulk type, what can be used?
  • Which of the following is NOT an example of cable pull calculations?
  • What type of pipe wrench is designed for turning and holding where marring is not objectionable?
  • In which scenario would you not need to apply a 1/4" bead of caulk?
  • After exposing a trench for direct buried cables, what should be added first?
  • What does the pulling head facilitate during wire installation?
  • What is a 7/8" channel or strut typically used for?
  • How is the variation of resistance of a conductor related to its area?
  • Insulators must be securely attached to any structure. What stresses are insulators designed to withstand?
  • For listed through penetrations, which condition must be met when using a different manufacturer's intumescent caulk?
  • Which construction type is referred to as 'Fire Resistive Construction'?
  • Why is it important to identify cable ties in a tray?
  • What are the primary load-bearing portions of a concrete frame constructed building called?
  • Which type of chisel is specifically used for cutting?
  • Which safety feature is critical for maintaining balance in a scaffold structure?
  • As conductor gauge size increases, what happens to the weight of the conductor?
  • Which National Electric Code (NEC) Chapter covers fire stopping requirements?
  • What type of lift do aerial work platforms essentially replace?
  • What should workers avoid when pulling wires into conduits with many bends?
  • The method of applying a 1/4" bead of caulk is meant to enhance what aspect of the installation?
  • What is meant by "Containment" in electrical installations?
  • For which type of conductors are the applications primarily residential and above ground installations?
  • What is the relationship between the increase in resistance and the area of a conductor?
  • If a switch is marked "CO/ALR," which types of conductors is it suitable for?
  • What is the responsibility of the employer regarding warning signs for energized electric circuits?
  • What is a 4" square box with eccentric knockouts suitable for?
  • When testing the firestop assembly, what is a crucial aspect of the manufacturer’s products being used?
  • What is a potential consequence of using the wrong size wrench on a nut or bolt?
  • Which conductor size is accepted by speed wire devices?
  • When cable ties are used in cable trays, they must be:
  • Fuses and circuit breakers are primarily designed to protect which of the following?
  • Can an intumescent caulk from one manufacturer replace that of another manufacturer without documentation when firestopping?
  • What level of current is described as causing a slight shock that is not painful but disturbing?
  • What is the primary binding material used to make mortar?
  • Which construction material is known for being renewable, recyclable, and for reducing the carbon footprint?
  • What is required of the employer before an electrical worker begins work near energized circuits?
  • What should an employee do if they must work near energized circuits?
  • What basic tool is used for cutting heavy cable and conduit?
  • Which type of aerial work platform is ideal for fitting into tight spaces due to its small footprint?
  • Which types of insulation are included in medium-voltage insulated conductors?
  • What is the standard size of knockouts found on a 4" square box?
  • What type of cover would you use for a 4-S box?
  • What is the purpose of grounding in device mounting?
  • What can happen if you use an oversized wrench on a nut?
  • What is the purpose of a short bushing in electrical installations?
  • What tool is best suited for general cutting tasks?
  • Is there a requirement to apply a 1/4" bead of caulk between a penetrating item and the wall or floor surface in point contact situations?
  • What statement is true regarding the role of employers in workplace electrical safety?
  • What is a 4" square mud ring used for?
  • What does mortar typically consist of?
  • What is a best practice for a worker pulling wire by hand?
  • In vertical installations, why are conductors typically placed at the top?
  • What is a common feature of duplex connectors in electrical applications?
  • What is commonly used to separate sleeping units in the same building?
  • Which series alloy is primarily used for aluminum conductors in structures?
  • What requirement is there for a listed electrical box installed in a fire-resistive wall without additional penetration protection?
  • What type of copper conductor is known for having the lowest conductivity and highest resistivity?
  • Which chapter of the IBC covers the requirements for fire-resistance rated wall and floor assemblies?
  • Which type of lift is specifically categorized by having an upward raising platform?
  • What is the main purpose of tooling the caulk during installation?
  • What does the T rating indicate in firestop assemblies?
  • Which type of barrier is specifically intended to restrict the movement of smoke?
  • Penetrations made in a smoke barrier require what in addition to the approved fire stop system?
  • Flat nose pliers are also known as what?
  • To prevent slipping, how should work platform boards be treated on rolling scaffolds?
  • What is the primary characteristic of cross-linked polyethylene insulation?
  • What is a primary characteristic of a firewall?
  • In electrical terms, what does FMC stand for?
  • What percentage of its strength does steel retain at 1200F?
  • Which engineered wood product is generally considered the least likely to be used on a jobsite?
  • Which of the following is not a valid application for type SE conductors?
  • What tool is specifically designed to cut larger cables and conductors?
  • What is the function of a masonry bit?
  • What system should be in place regarding hazards in a permit-required confined space?
  • What should be used for adjusting uneven grade conditions when erecting scaffolding?
  • What are the three basic parts of a screwdriver?
  • What is the ideal direction for pulling wires to minimize force?
  • A business type occupancy is classified as one where:
  • Which lift is characterized as a push around type that serves as a ladder replacement?
  • What should workers consider when moving large wire spools?
  • Multi-roller sheaves are commonly referred to as what type of hook sheaves?
  • 15- and 20-amp duplex receptacles not marked with "CO/ALR" are suitable for use with which conductors?
  • At what temperature does steel begin to lose strength?
  • Which of the following statements is false about engineering judgements?
  • Which of the following is NOT a fundamental kind of stress that building materials are subjected to?
  • What type of studs are typically used for building interior partition walls?
  • What might occur if an open-end wrench is used with too large of an opening for the job?
  • The statement "ANSI defines 'Familiarization' of MEWPs as instructions to enable the trainee to become a qualified person" is considered what?
  • When planning a wire pull, what is a best practice?
  • When installing aluminum conductors inside a structure, which series alloy must be used?
  • The International Building Code (IBC) classifies every building primarily based on what two criteria?
  • What document outlines the requirements for firestop products?
  • Type AC armored cable is governed by which UL standard?
  • What are the primary functions of a device's mounting strap?
  • What is the primary role of an attendant in a permit-required confined space?
  • Which assembly rating reflects the hours a firestop assembly will not exceed a set temperature?
  • What should you prioritize when lashing cables in cable trays?
  • What does ANSI define as “Familiarization” of MEWPs?
  • In toolbox organization, which tool is best suited for precision work in tight spaces?
  • What construction does the mare's tail method mimic when creating a wire pulling head?
  • A permit-required confined space is defined as containing or having the potential to contain what?
  • What do you call a tool used to grip and turn pipes securely?
  • According to the IBC, which chapter covers the requirements for fire-resistant rated assemblies?
  • What material is preferred for bedding in a trench installation?
  • What is generally not considered an outlet by the NEC?
  • Aerial cable bus conductors take up how much space compared to bare conductors installed on a pole?
  • What is the primary function of columns in concrete frame construction?
  • When should cable pull calculations ideally be performed?
  • What is the equivalent of 0.25' in mils?
  • Are receptacle contacts available in multiple designs based on amperage and voltage?
  • Fishsticks are typically made of what material?
  • Which tool is specifically designed to grip and turn pipes?
  • What role does wood play in sustainable construction practices?
  • What should be done when a confined space entry situation arises involving severe injury?
  • Which type of wrench is preferable for use on delicate surfaces without causing damage?
  • What is the function of the "CO/ALR" marking on devices?
  • Is it necessary to document the acceptance when substituting intumescent caulks from different manufacturers?
  • What is the simplest method to get wires and cables into a cable tray?
Subscribe

Get the latest from Examzify

You can unsubscribe at any time. Read our privacy policy